Goat Milk and Honey Soap
Though a Castile bar was the first soap recipe I made, I dreamed of making a Goat Milk and Honey Soap bar. Well, here it is. Using milk and honey in a recipe means you need to be aware of a few more things, but it’s pretty easy once you get the hang of it. Enjoy the many nourishing benefits of this soap!
Equipment
- Large stainless steel pot
- Large spoon
- Scale
- Bowls for measuring ingredients
- [Stick Blender]
- small zip top bag
- Soap Loaf Mold
- Parchment Paper
- Rubber Spatula
- Measuring Spoons
Ingredients
- 10 ounces olive oil
- 8 ounces lard
- 8 ounces coconut oil
- 4 ounces sweet almond oil
- 2 ounces beeswax
- 4 ounces lye
- 8 ounces filtered water
- 4 ounces goat milk
- 1 ounce orange essential oil
- 1 Tablespoon raw honey
Instructions
Safety First!
- Remember to wear your safety equipment and mix the lye water outside. Tell everyone you live with that where you’re working is off limits. Give yourself enough time to complete the recipe.
Prep Ahead
- Combine the water and milk in a large glass, plastic, or stainless steel container. Place milk-water into the freezer for 1 to 2 hours. It is okay if a slush forms, as long as it doesn’t freeze. The colder your milk-water, the lighter your soap will be after adding the lye.
Make Soap
- Heat the Fats/Oils: In a large pot over medium-low heat, combine olive oil, lard, coconut oil, sweet almond oil, and beeswax. Heat until they are melted and incorporated. Remove from heat and allow to cool to 90-100°F.
- Mix the Lye-Water: Put on protective gear including a mask, gloves, and long sleeves. Outside, very slowly pour only ¼ of the lye into the milk-water and stir until dissolved. Let cool for 20 minutes. Repeat until all lye is dissolved into the milk-water. If milk still browns, don’t worry. Your soap will just be darker. Allow to cool to 90-100°F. If oil or lye water cool at different rates, you can use a cold or hot water bath in the sink.
- Prepare the Mold: While the oils and lye water cool, line the mold with parchment paper.
- Combine and Bring to Trace: When both oils and lye water are around 90-100°F, pour the lye water into the pot of oils. Use a stick blender or hand mixer to mix for 1 to 2minutes and then let the mixture rest for 4 to 5 minutes. Repeat mixing and resting until light trace.
- Mix in Natural Additives: When soap reaches light trace, add essential oils and honey and blend for 30 seconds.
- Mold the Soap: Pour the soap mixture into the mold, cover with a lid or parchment paper for 24 hours. Do not insulate unless your house is below 75°F, then insulate by placing a towel around the outside edges to avoid a partial gel.
- Cut and Cure: Remove soap from the mold. If it seems too soft to remove, wait another 12 to 24 hours before removing. Cut the soap into twelve 4-ounce bars. Allow the bars to cure for 4 to 6 weeks.
Notes
Yield: 3 pounds or twelve 4-ounce bars
Lye Discount: 15%
Label: Moisturizing
Start to Finish Time: 2 hours, 24 hours in mold, 4 to 6 weeks to cure
Scent: Orange Tips: Milk can scald when lye is added. Placing the milk-water in the freezer until it’s very cold helps prevent this. Be sure to add lye slowly. It is okay to really take your time, coming back every 20 minutes to add a little more. Adding milk can also make your batch get hotter than usual, so just insulate a milk recipe lightly with a towel if you’re concerned about getting a good gel for color. Honey can also make soap come to trace faster, so add it and blend really well right before pouring soap into the mold.
Lye Discount: 15%
Label: Moisturizing
Start to Finish Time: 2 hours, 24 hours in mold, 4 to 6 weeks to cure
Scent: Orange Tips: Milk can scald when lye is added. Placing the milk-water in the freezer until it’s very cold helps prevent this. Be sure to add lye slowly. It is okay to really take your time, coming back every 20 minutes to add a little more. Adding milk can also make your batch get hotter than usual, so just insulate a milk recipe lightly with a towel if you’re concerned about getting a good gel for color. Honey can also make soap come to trace faster, so add it and blend really well right before pouring soap into the mold.
Tried this recipe?Let us know how it was!